Finishing MDF panels

    Poresh make repairs in the corridor (front) in their own home, as it were, in a simple way to somehow arrange meaningless forbidding walls of my wife and I first decided a voprosets what material to use. First analyzed voprosets that the plaster all the walls, and later to paint, and later in the presence of money make a decorative treatment. Few people know that there is a significant shortage of plaster is that in winter prepare the working solution is brought indoors, and it is a furious amount of dust, and The mud in your home. It should be emphasized that the second reason is that the walls of our dwellings are far from completely straight and perfectly realize this kind of work can only be a team of employees who specialize in this and have all aspects of billing, beacons, reinforcing fatty layer of plaster, etc . on. It goes without saying-, third reason - the highest price, if you realize not work, and workers. Then they decided to addressed, as we call it, the Universal Mind - Webu! Overlooking, a number of websites on a construction theme, pritopali to the conclusion that one of the most comfortable materials are MDF panels.

  This material has many advantages:A. Ratio of the value and properties of very divine.Two. Ability to align at least some curvature of the wall.Three. You do not need a preparatory sanding of the walls.4. The possibility of combining the colors and the width of the panels, net (including on iskosok), which also provides extensive capabilities in the design delights.Five. Working with the material is not asking for special training and be able to cope with it, as many put it, at least some beginner.6. We need a small tool kit.7. Extremely stable to excessive moisture, rust, and - strainsEight. Dismantlement, as all the panels, and a warped does not cause much difficulty.9. Just an ordinary wash cloth or moistened wipes.There are drawbacks:A. Not the highest solidity. It would be bad if we did not notice that because you have to be careful. Of course, we all know very well that not a very powerful blow can destroy the bar, but its just a spoof.Two. MDF panels are perfect blaze. It's no secret that not emit when burned an entire mountain corrosive combustion products like plastic. Everyone knows that just be careful with fire, and hide the wiring in the self-extinguishing corrugation.Three. Not waterproof.Not the most complex in the lining is also made of wood, but in my eyes the corridor (front) exhaust lining though and nice-looking but no longer recalls the balcony, or bathhouse. It's no secret that although the environmental characteristics of the trees lining in not competition.Various types of plastic lining or plastic panels of favorite in the near future were not analyzed because of environmental and fire protection features in my eyes can not tolerate nor any criticism.Thus, the material chosen - begin to work!Often abused to define inventory.For the work we need:A. Electric drill (for mounting rails).Two. Jig (if there is no suitable, as people are used to express, hand saws for wood and red-hot small tooth).Three. Roulette.4. Hammer.Five. Driver (if not, fit standard Phillips screwdriver, although this period of increment).6. Level (in the standard laser, but it is possible to manage the construction and hydraulic, though it also does not contribute to speeding up the process).If you decided to handle the ceiling and wall panels of MDF, then set to work to the ceiling. It's no secret that I'll be tinkering mirrored ceiling, and therefore start from the walls.To align the use of oblique walls of the wood rail, which is being implemented in all stores operation section 20 or 20 * 40 * 50. Of course, to say, we mark up the wall by 40 cm (you can often not be worse). All have long known that the strength of panels rather that there was no deflection when oblakachivanii on the wall. I'd like to stress that our rail mounted on a wall with plastic plugs and screws. And do not even have to say that if the wall is quite smooth, ie leans less than 1.5-2 cm then the screw is 50 mm full enough, if more of the bleeding screws elect criterion. I'd like to stress that drills holes for dowels, hammer, hammering them back, and strengthening our self-tapping rail to the wall plug. It should be noted that the distance between the screws 40-70 cm is no longer needed. Few people know that afterward fastening strips across the wall or rail puts rovnenko rule to control the vertical level. It should be noted that the twisting and slipping "pads" under the rail alignment vertical level. Needless to say, as "pads" You can use small pieces of rack chop into pieces of varying thickness. It should be emphasized that the rail can be sewn as a brick wall and the wall of plasterboard.But in the benchmark Instead of the wood slats can be applied and the iron profile, and suspensions for perfect vertical and make the hard structure, but it is many times the price increment. I'd like to emphasize that because I used at rail. Of course, we all know very well that the corridor because I have dry and then heated rack never lead, and hardness of the design will be excellent, with the circumstance that the rail is dry.The subsequent step. It should be noted that expose how people used to express, the first panel of MDF with the level and fix it with, as usual, a special bracket (klyaymera), which supplies a hidden fastening panels between them. Everyone knows that you should not use screws, strengthens klyaymerami just because MDF panels are required to breathe. As if this were not enough, but klyaymery finishing nails to nail stakes. Few people know that all the subsequent reinforcing bar in the butt to previous and fix on how many people think of each rail. Where the door should avoid use of electric jigsaw or hacksaw to prirezki panels. And do not even have to say that the holes for outlets and switches to cut crown timber zapamyatovyvayte Not all the electrical wires to hide in the corrugations. Please note that this measure can prevent a fire in the episode rather short-circuit wiring.Internal and external corners, and joints of the door panels and edging camouflage vseprigodnymi angles, which are mounted on the watery nails type MR-90 or any other, but I like fast, as everyone knows, watery grasp the nails in this case there is no need to use the mounting tape. Few people know that if you still eat the mounting tape, remove it slowly so as not to destroy the panelThe last step - strengthening the plinth. Sure, it is worth mentioning that the outer corners and caps before attaching a little grease inside the watery nails to give dobornoy fortress.